Order some relevant reference designator. Use JP for all jumpers. Place
silkcreen neatly. Add some custom silk screen. Remove heat sink corner
marks on silk screen.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Changes:
Footrints:
-Modified DC Jack to accomodate CUI PJ-002A
-Modified RJ45 to increase clearance between shield and poe pins
-Modified m.2 mounting pads to avoid drc errors
Schematic:
-usb-c facing usb mux is supplied by +3v3VP
-added misc. capacitors
PCB
-min. annular ring for vias set to 0.125 from 0.2
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Use JLC7628 impedance values to get more options in color selection.
Also this leads to slightly wider traces typically, and it will be
easier to switch back to JLC2313 or the like than the other way around.
Also swap placing of HDMI/SW2 and rotate the heatsink by 90° for easier
routing.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Adjust some high level placement like M.2 or CM4 and heatsink. Remove
all traces and vias since most of the layouting has to be redone
anyways.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Use Diodes B2100-13-F consistently
- Define part for pin headers
- Replace N-Channel MOSFET for PoE with BSZ440N10NS3GATMA1
- Define Input protection MOSFET DMP3013SFV-7
Signed-off-by: Stefan Agner <stefan@agner.ch>
Remove power/reset/recovery switch. Power and reset is not really required
and recovery mode (USB Boot) can be triggered via jumper. Make the Fan
and RPiLED a new separate config so we can leave them unpopulated. Add a
second GPIO controlled switch.
Fixes: #16
Signed-off-by: Stefan Agner <stefan@agner.ch>
Make sure those signals are well defined even when not be driven from
the CM4 side. Also rename Radio.BOOT to Radio.~BOOT since its a low
active signal.
Fixes: #10
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add the CM4 board to board connectors using separate symbols. This is a
bit a hack, but makes sure two pieces appear in the BOM.
Also, this seems to upgrade all the schematic to the latest KiCad
schematic version.
Signed-off-by: Stefan Agner <stefan@agner.ch>
changes:
-more routing
-added poe negotiation disabled when +12V is present on the DC jack
-modified m.2 "holes"
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Make sure property ids are unique within a symbol. This should avoid
that Manufacturer properties disappear in the future.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Fix footprint for 02x05 pin header
- Add footprint for Bourns SDR1006 Inductor (PoE)
- Define footprints for inductors
- Define footprints for ferrite beads
- Define footprint for fuse
- Define footprints for all resistors
- Define footprints for SD card and other components
- Switch ON Semi NCP114MX with TI TLV73333PDBV
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Moved PoE to a seperate sheet and finished design
- Started using Config field for Variants and DNP flag
- Fix-ups
- Added Wurth 749119550 and TI TPS23734 to the symbol library
- Changed RTC from PCF8563 to PCF85063
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added sdcard sheet and SD bus
-changed main i2c bus
-added 1.8V and 3.3V connection to CM4
-removed clk32 from led driver
-fixed PCM interface Data pin
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added AP64501SP-13 library symbol
-Initial power supplies schematics
-Increased capacitance for PCIe socket
-Connections between sheets
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added net classes for controlled impedance traces
-Added power hierarchical sheet
-Initial USB subsystem schematic
-Added multiple bus definitions (usb, pcie, i2c etc.)
-Fixed busses use
-Added LDO for audio analog rails
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
