Remove power/reset/recovery switch. Power and reset is not really required
and recovery mode (USB Boot) can be triggered via jumper. Make the Fan
and RPiLED a new separate config so we can leave them unpopulated. Add a
second GPIO controlled switch.
Fixes: #16
Signed-off-by: Stefan Agner <stefan@agner.ch>
Use a through hole 3.5mm Audio jack to make sure it does nto get teared
off the board accidentially that easily.
Fixes: #9
Signed-off-by: Stefan Agner <stefan@agner.ch>
Make sure those signals are well defined even when not be driven from
the CM4 side. Also rename Radio.BOOT to Radio.~BOOT since its a low
active signal.
Fixes: #10
Signed-off-by: Stefan Agner <stefan@agner.ch>
Use the correct footprint for the PoE bulk capacitor C80. The TI
evaluation module circuit uses a Panasonic EEE-FK1J470P bulk capacitor.
The series has other better suited alternatives like EEE-HA1J470UP, but
the F-size code seems to be a sensible choice.
Fixes: #1
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add the CM4 board to board connectors using separate symbols. This is a
bit a hack, but makes sure two pieces appear in the BOM.
Also, this seems to upgrade all the schematic to the latest KiCad
schematic version.
Signed-off-by: Stefan Agner <stefan@agner.ch>
changes:
-more routing
-added poe negotiation disabled when +12V is present on the DC jack
-modified m.2 "holes"
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
The 1- at the start of the part number denotes M-Key which is a rather
important distinction. Fix the footprint name.
Signed-off-by: Stefan Agner <stefan@agner.ch>
We don't plan to populate those connectors by default. The through-hole
ones are easier to solder by hand on a populated PCB.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Fix footprint for 02x05 pin header
- Add footprint for Bourns SDR1006 Inductor (PoE)
- Define footprints for inductors
- Define footprints for ferrite beads
- Define footprint for fuse
- Define footprints for all resistors
- Define footprints for SD card and other components
- Switch ON Semi NCP114MX with TI TLV73333PDBV
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add footprint for PoE controller TI TPS23734. Also fix/readd
Manufacturer which somehow got lost when opening.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Moved PoE to a seperate sheet and finished design
- Started using Config field for Variants and DNP flag
- Fix-ups
- Added Wurth 749119550 and TI TPS23734 to the symbol library
- Changed RTC from PCF8563 to PCF85063
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added sdcard sheet and SD bus
-changed main i2c bus
-added 1.8V and 3.3V connection to CM4
-removed clk32 from led driver
-fixed PCM interface Data pin
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added AP64501SP-13 library symbol
-Initial power supplies schematics
-Increased capacitance for PCIe socket
-Connections between sheets
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added net classes for controlled impedance traces
-Added power hierarchical sheet
-Initial USB subsystem schematic
-Added multiple bus definitions (usb, pcie, i2c etc.)
-Fixed busses use
-Added LDO for audio analog rails
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
