Adjust silk screen graphics to match current layout. Adjust silk screen
reference designator placements. Bump date and version of schematics and
PCB.
Signed-off-by: Stefan Agner <stefan@agner.ch>
-Snubber circuit under ecrtail load condition can dissipate more power
then the resistor can handle, increased the resistor size and added one
more in parallel
-Increased size of some of the 12V input capacitors
-Use 3.3Vp instead of 3.3V generated by the RPi for LED, RTC, Radio, Fan
control and RPi reduced hat connector
-PoE pri/sec capacitor value changed
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
decreased coupling between poe lines and the gnd plane
added vias to stich main gnd planes
decreased the peak current through the transformer
inductor based pi filter on the poe output
decreased coupling to gnd of the poe "noise path"
added parallel mosfet capacitance to poe
moved fb line fo the dcdcs away from inductors
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Increment to sub-version v1.2. Main changes are:
- Back and front silk screen
- LED resistors
There are no changes in the layout and any critical components.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Modified PoE layout to account for GNDS-GND1 flow
and repositioned the noise retern capacitor.
Snubber was corrected for the transformer used and the switching
frequency. Some components were removed.
PoE Input filter was adjusted.
3.3 and 5V DCDC capacitor layout was optimised and unused components
were removed.
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
- Fix edge cut on lower right corner to make board size exact
- Update board charactristics
- Set grid origin back to 30, 30
- Update M.2 expansion silk screen (remove AI accelerator hint)
- Various silk screen reference designator fixes/improvements
- Add ESD warning logo
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Update silk screen reference designators
- Update backside silk screen for Yellow revision 1.1
- Set U21 (SOIC-8 RTC) to assemble and U25 (MSOP-8) as DNP
- Update heatsink footprint to add heatsink outline to silk screen (#44)
- Mark orientation of D26, D27, D28 and D29 (fixes#39)
- Use pin-header footprint for PoE selector J13, it is now JP5
Signed-off-by: Stefan Agner <stefan@agner.ch>
-Fixed upstream diff pair polarity
-added optional inverer for the USB power switch enable pin
Design now supports both AP2181 and AP2191
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Run annotation again which just updated some net names. Address various
DRC issues like courtyard violence and exclude the remaining DRC errors.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- U7: Define Manufacturer/PartNumber
- J13: Define Manufacturer/PartNumber
- L2: Fix PartNumber (remove unprintable characters)
- C85: Change to our preferred supplier Nichicon
- J9: DNP (not used by default, avoid potential issues with FCC approval)
- Y1/Y2: Define frequency and load capacitance in value
- JP1: Use sensible part value
- C106: Fix Config field
- Remove heat sink and CM4 from BOM (handled in product assembly BOM)
Signed-off-by: Stefan Agner <stefan@agner.ch>
PoE
-Added a common mode filter on the input
-FB filter on the output side
-12V in now disables the poe with the DEN pin
-DT is now disabled
-PSRS is now disabled
-move to 1210 resistors for resistors identified in thermal testing
-DTHR is now enabled in default BoM
-some resistor values were adjusted
-some caps were moved to the common power supply section
USB:
-USB Hub 1.8V rail have capacitors added
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Add BD9D321EFJ to the symbol library and align it properly to the
1.27mm/0.050inch grid. Make sure to align the instances U15/U16
correctly as well as the complete Power schematic.
With that GND is now correctly connected to Pin 5 of U16.
Fixes: #27
Signed-off-by: Stefan Agner <stefan@agner.ch>
updates
schematic:
-change usb current protection IC to 1.5A
-Added low-pass filter to the audio output
-PoE fixed primary windings polarity
-added option to select poe class with a jumper (between 3 and 4)
-fixes in poe design
-added testpoints
-added virtual hirose df40c connectors for pick and place use
lightblue.pretty:
-added fake DF40C footprint for pick and place and 3d model purposes
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Changes:
Footrints:
-Modified DC Jack to accomodate CUI PJ-002A
-Modified RJ45 to increase clearance between shield and poe pins
-Modified m.2 mounting pads to avoid drc errors
Schematic:
-usb-c facing usb mux is supplied by +3v3VP
-added misc. capacitors
PCB
-min. annular ring for vias set to 0.125 from 0.2
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
- Replace unusual/high value ceramics with lower value in parallel
- Use the same protection Shottky Diode in PoE as in regular input
(B340LB-13-F)
- Replace PoE rectifier Diodes with B1100-13-F
- Replace PoE Inductor (SRN6045TA-3R3Y) with the same part from 5V power
supply (Taiyo Yuden NRS8030T3R3MJGJ)
- Correctly specify Pulse Electronics transformer
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Use Diodes B2100-13-F consistently
- Define part for pin headers
- Replace N-Channel MOSFET for PoE with BSZ440N10NS3GATMA1
- Define Input protection MOSFET DMP3013SFV-7
Signed-off-by: Stefan Agner <stefan@agner.ch>
The Rohm has a lower current rating and input voltage range, but should
be good enough for our use case. It has better availability and is quite
a bit cheaper than the Diodes part. This also requires different
inductors and some different resistor values.
Fixes: #12
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add the CM4 board to board connectors using separate symbols. This is a
bit a hack, but makes sure two pieces appear in the BOM.
Also, this seems to upgrade all the schematic to the latest KiCad
schematic version.
Signed-off-by: Stefan Agner <stefan@agner.ch>
changes:
-more routing
-added poe negotiation disabled when +12V is present on the DC jack
-modified m.2 "holes"
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
- Fix footprint for 02x05 pin header
- Add footprint for Bourns SDR1006 Inductor (PoE)
- Define footprints for inductors
- Define footprints for ferrite beads
- Define footprint for fuse
- Define footprints for all resistors
- Define footprints for SD card and other components
- Switch ON Semi NCP114MX with TI TLV73333PDBV
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Moved PoE to a seperate sheet and finished design
- Started using Config field for Variants and DNP flag
- Fix-ups
- Added Wurth 749119550 and TI TPS23734 to the symbol library
- Changed RTC from PCF8563 to PCF85063
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added AP64501SP-13 library symbol
-Initial power supplies schematics
-Increased capacitance for PCIe socket
-Connections between sheets
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
-Added net classes for controlled impedance traces
-Added power hierarchical sheet
-Initial USB subsystem schematic
-Added multiple bus definitions (usb, pcie, i2c etc.)
-Fixed busses use
-Added LDO for audio analog rails
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
