Cleanup some fill zones.
Updated the Transformer symbol with pin 4, connected to +48V for better
zone fill.
fixed top/bottom transition for the DC_IN_F
Added some gnd vias
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Modified PoE layout to account for GNDS-GND1 flow
and repositioned the noise retern capacitor.
Snubber was corrected for the transformer used and the switching
frequency. Some components were removed.
PoE Input filter was adjusted.
3.3 and 5V DCDC capacitor layout was optimised and unused components
were removed.
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
- Fix edge cut on lower right corner to make board size exact
- Update board charactristics
- Set grid origin back to 30, 30
- Update M.2 expansion silk screen (remove AI accelerator hint)
- Various silk screen reference designator fixes/improvements
- Add ESD warning logo
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Update silk screen reference designators
- Update backside silk screen for Yellow revision 1.1
- Set U21 (SOIC-8 RTC) to assemble and U25 (MSOP-8) as DNP
- Update heatsink footprint to add heatsink outline to silk screen (#44)
- Mark orientation of D26, D27, D28 and D29 (fixes#39)
- Use pin-header footprint for PoE selector J13, it is now JP5
Signed-off-by: Stefan Agner <stefan@agner.ch>
-Fixed upstream diff pair polarity
-added optional inverer for the USB power switch enable pin
Design now supports both AP2181 and AP2191
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
Run annotation again which just updated some net names. Address various
DRC issues like courtyard violence and exclude the remaining DRC errors.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Change FL1 to be Murata Electronics DLW5BTM102SQ2. This version is not
automotive approved. It is cheaper and has better availability
currently.
Signed-off-by: Stefan Agner <stefan@agner.ch>
- U7: Define Manufacturer/PartNumber
- J13: Define Manufacturer/PartNumber
- L2: Fix PartNumber (remove unprintable characters)
- C85: Change to our preferred supplier Nichicon
- J9: DNP (not used by default, avoid potential issues with FCC approval)
- Y1/Y2: Define frequency and load capacitance in value
- JP1: Use sensible part value
- C106: Fix Config field
- Remove heat sink and CM4 from BOM (handled in product assembly BOM)
Signed-off-by: Stefan Agner <stefan@agner.ch>
PoE
-Added a common mode filter on the input
-FB filter on the output side
-12V in now disables the poe with the DEN pin
-DT is now disabled
-PSRS is now disabled
-move to 1210 resistors for resistors identified in thermal testing
-DTHR is now enabled in default BoM
-some resistor values were adjusted
-some caps were moved to the common power supply section
USB:
-USB Hub 1.8V rail have capacitors added
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
updates
schematic:
-change usb current protection IC to 1.5A
-Added low-pass filter to the audio output
-PoE fixed primary windings polarity
-added option to select poe class with a jumper (between 3 and 4)
-fixes in poe design
-added testpoints
-added virtual hirose df40c connectors for pick and place use
lightblue.pretty:
-added fake DF40C footprint for pick and place and 3d model purposes
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
2.2uF/100V are not really available in a 0805 package. This part of
the PoE design a 25V rating is sufficent.
Fixes: #22
Signed-off-by: Stefan Agner <stefan@agner.ch>
Order some relevant reference designator. Use JP for all jumpers. Place
silkcreen neatly. Add some custom silk screen. Remove heat sink corner
marks on silk screen.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Changes:
Footrints:
-Modified DC Jack to accomodate CUI PJ-002A
-Modified RJ45 to increase clearance between shield and poe pins
-Modified m.2 mounting pads to avoid drc errors
Schematic:
-usb-c facing usb mux is supplied by +3v3VP
-added misc. capacitors
PCB
-min. annular ring for vias set to 0.125 from 0.2
Signed-off-by: Dominik Sliwa <dominik@sliwa.io>
- Replace unusual/high value ceramics with lower value in parallel
- Use the same protection Shottky Diode in PoE as in regular input
(B340LB-13-F)
- Replace PoE rectifier Diodes with B1100-13-F
- Replace PoE Inductor (SRN6045TA-3R3Y) with the same part from 5V power
supply (Taiyo Yuden NRS8030T3R3MJGJ)
- Correctly specify Pulse Electronics transformer
Signed-off-by: Stefan Agner <stefan@agner.ch>
- Use Diodes B2100-13-F consistently
- Define part for pin headers
- Replace N-Channel MOSFET for PoE with BSZ440N10NS3GATMA1
- Define Input protection MOSFET DMP3013SFV-7
Signed-off-by: Stefan Agner <stefan@agner.ch>
