mirror of
https://github.com/dekuNukem/USB4VC.git
synced 2025-10-31 11:26:46 -07:00
124 lines
3.2 KiB
Markdown
124 lines
3.2 KiB
Markdown
# USB4VC Kit Assembly
|
|
|
|
[Get USB4VC](https://www.tindie.com/products/dekuNukem/usb4vc-usb-inputs-on-retro-computers/) | [Official Discord](https://discord.gg/HAuuh3pAmB) | [Getting Started](getting_started.md) | [Table of Contents](#table-of-contents)
|
|
|
|
----
|
|
|
|
Thanks for getting USB4VC! Here is a quick guide on how to put everything together.
|
|
|
|
## Recommended Tools
|
|
|
|
A small Phillips-head screwdriver (`+`shape) should be included in the package.
|
|
|
|
A pair of pliers would make tightening the fasteners easier, but not required.
|
|
|
|
## Handling Bare Circuit Boards
|
|
|
|
To reduce the risk of damage from static discharge:
|
|
|
|
* Wash your hands first
|
|
|
|
* Always hold the circuit board by its edge
|
|
|
|
* Don't touch the components
|
|
|
|
## Assembly Steps
|
|
|
|
By now, you should have:
|
|
|
|
* USB4VC Baseboard
|
|
|
|
* USB4VC Protocol Card(s)
|
|
|
|
* Raspberry Pi 1/2/3/4 Model B
|
|
|
|
* Acrylic Plates
|
|
|
|
* Mini Screwdriver
|
|
|
|
* Fasteners
|
|
|
|
* Anti-slip feet
|
|
|
|
|
|
|
|
You should have the following fasteners, take note of what they look like :)
|
|
|
|
|
|
|
|
Start by peeling off the protective layer on acrylic plates:
|
|
|
|
|
|
|
|
Orient plate the plate as shown, insert four `8mm Screws` into the marked holes:
|
|
|
|
|
|
|
|
Put something rigid (cardboard, etc) over the screws, and flip the whole thing over.
|
|
|
|
The screws should stay in place, insert four `2.5mm Spacers` over the screws:
|
|
|
|
|
|
|
|
Put the Baseboard over the screws, and install four `11mm Standoffs`, moderately tighten.
|
|
|
|
|
|
|
|
Plug your Raspberry Pi into the pin headers, push down gently until fully inserted, make sure everything is lined up.
|
|
|
|
Put four `2.5mm Spacers` over the holes.
|
|
|
|
|
|
|
|
Position the top plate over the holes, make sure the plastic standoffs are not displaced.
|
|
|
|
Screw the four `8mm Screws` into the metal standoffs underneath.
|
|
|
|
|
|
|
|
Insert two `4mm Screws` from the underside.
|
|
|
|
|
|
|
|
Install two `4mm Standoffs` from top. **DO NOT OVER-TIGHTEN!** Otherwise you might crack the acrylic. Finger-tight is OK.
|
|
|
|
|
|
|
|
Insert the Protocol Card into the connector, and secure it with two `4mm Screws`.
|
|
|
|
|
|
|
|
Flip it over, clean the area if dirty, and stick on the anti-slip feet on the corners:
|
|
|
|
|
|
|
|
If your package came with labels, attach them like so:
|
|
|
|
|
|
|
|
And you're done! Congratulations!
|
|
|
|
Head back to the [Getting Started Guide](getting_started.md#kit-assembly) to see how to use it.
|
|
|
|
|
|
|
|
## Questions or Comments?
|
|
|
|
Feel free to ask in [official Discord](https://discord.gg/HAuuh3pAmB), raise a [Github issue](https://github.com/dekuNukem/USB4VC/issues), [DM on Twitter](https://twitter.com/dekuNukem_), or email `dekunukem` `gmail.com`!
|
|
|
|
## Table of Contents
|
|
|
|
[Main page](README.md)
|
|
|
|
[(Youtube Video) USB4VC in Action](https://www.youtube.com/watch?v=54sdPELuu4g)
|
|
|
|
[Getting Started Guide](getting_started.md)
|
|
|
|
[Kit Assembly Guide](kit_assembly.md)
|
|
|
|
[Tinkering Guide / Make Your Own Protocol Card / Technical Notes](technical_notes.md)
|
|
|
|
[Kickstarter Acknowledgements](kickstarter_info.md)
|
|
|
|
|